Mechanical Aptitude Tests
Mechanical aptitude tests

Mechanical principles for aptitude tests, with worked examples

By Mechanical Aptitude Tests editorial teamUpdated 16 min read

Short answer: nearly every mechanical aptitude question uses one of about ten rules. The big one is that work in equals work out: a lever, pulley, ramp or hydraulic press lets you use less force only by moving further. The others cover gear direction and speed, pressure in fluids, falling objects, stability, heat expansion and simple circuits. Learn each rule with one example below, and you can answer most questions in under 30 seconds.

Each section gives the rule, a worked example with numbers, and the trap that catches people. Try each example before reading the working.

How do gears work?

Rules:

A 20-tooth gear turning at 150 rpm drives a 50-tooth gear. How fast does the larger gear turn?

20 × 150 = 50 × speed, so speed = 3,000 / 50 = 60 rpm.

Sense check: the driven gear is bigger, so it must be slower than 150.

Trap: size never changes direction. An idler gear between two gears changes direction but not the speed ratio between the first and last gears.

How do belts and chains work?

A 20 cm pulley at 240 rpm drives a 60 cm pulley with a belt. How fast does the large pulley turn?

20 × 240 = 60 × speed, so speed = 4,800 / 60 = 80 rpm.

Bicycles work the same way: a low gear (small front sprocket, large rear sprocket) makes pedaling easier uphill because it reduces the force needed, at the cost of more pedal turns per wheel turn.

How do levers balance?

Rule: force × distance from the fulcrum is equal on both sides when the lever balances. This product is called the moment or torque.

A 300 N load sits 1.0 m from the fulcrum. You push 2.0 m from the fulcrum on the other side. What force balances it?

300 × 1.0 = force × 2.0, so force = 150 N.

The same rule explains why a longer wrench loosens a rusted nut more easily: the same push at twice the distance gives twice the turning force. On a seesaw with two people, the heavier person must sit closer to the middle.

Three classes of lever: fulcrum in the middle (seesaw, crowbar), load in the middle (wheelbarrow, nutcracker), or effort in the middle (tweezers, fishing rod). The balance rule works for all three.

How do pulleys reduce effort?

Rule: count the rope segments that support the moving pulley block. Ignoring friction, the force you need is the load divided by that number.

A 200 N load hangs from a movable pulley supported by two rope segments. How far must you pull the rope to lift the load 1 m?

Both segments must shorten by 1 m, so you pull 2 m of rope. Force is halved (100 N), distance is doubled: work in equals work out.

How do ramps, wedges and screws work?

Rule: force along the ramp × ramp length = weight × height (on a frictionless ramp).

A 400 N cart is pushed up a frictionless ramp 8 m long and 2 m high. What force is needed?

Force × 8 = 400 × 2, so force = 800 / 8 = 100 N.

A wedge is a ramp you push into something: its mechanical advantage is roughly length divided by thickness, so a 15 cm wedge that is 5 cm thick at the back has an advantage of about 3. A screw is a ramp wrapped around a cylinder: finer threads mean more turns but less effort.

How does hydraulic pressure work?

Rule: pressure in a closed fluid is the same everywhere (Pascal's principle). Pressure = force / area, so a bigger piston gets a bigger force.

A hydraulic press has a 4 cm² small piston and a 24 cm² large piston. You push the small piston with 150 N. What force does the large piston give?

The area ratio is 24 / 4 = 6, so the force is 150 × 6 = 900 N.

The catch: the large piston moves one sixth as far as the small one.

Other fluid rules that come up:

What do you need to know about gravity and motion?

What makes an object stable?

Rule: an object tips when its center of gravity moves outside its base. A low center of gravity and a wide base give the most stability.

Typical questions show loads placed at different heights on a truck or shelf and ask which is most likely to tip. Pick the one with the weight highest up and the narrowest base. When carrying a load, the person closer to the load carries more of its weight.

Heat, sound and light: which rules come up?

Which electricity rules appear on mechanical tests?

Springs: what do you need to know?

A spring stretches in proportion to the force on it. Two identical springs side by side (in parallel) share the load, so the pair stretches half as far, like one spring twice as stiff. Two springs end to end (in series) each feel the full load, so the pair stretches twice as far.

How fast should you answer?

If a picture is not clicking after 40 seconds, guess, note it and move on. Most questions are quick once you spot the rule, so time saved there pays for the hard ones.

Put the rules to work: full-length practice tests with diagrams and worked answers.

Take a practice test

Frequently asked questions

What is the most important rule for mechanical aptitude tests?

Conservation of work: a machine can reduce the force you need, but only by making you push over a longer distance. Force times distance in equals force times distance out. Levers, pulleys, ramps, gears and hydraulics all follow it.

How do you tell which way a gear turns?

Meshed gears turn in opposite directions. In a chain, every other gear turns the same way as the first. Gears on the same shaft turn together, the same way.

Does a bigger gear turn faster or slower?

Slower, with more torque. Teeth times rpm is equal on both gears, so a gear with three times the teeth turns at one third of the speed.

How do you count pulley mechanical advantage?

Count the rope segments that hold up the moving block (not the ones going to a fixed point you pull down on). Divide the load by that number to get the force needed, ignoring friction.

Sources